. ND-45669 (E) ISSUE 2 PART OF STOCK # 151901 ® Command Manual DECEMBER, 1997 NEC America, Inc. NEC America, Inc. Reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America, Inc. Has prepared this document for use by its em- ployees and customers.
The information contained herein is the property of NEC America, Inc. And shall not be reproduced without prior written approval from NEC America, Inc. 44-1 44-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 1/7 ND-45669 (E) ISSUE 2.
View and Download NEC NEAX 2000 IPS configuration manual online. NEC Electronics America Server User Manual. NEAX 2000 IPS Server pdf manual download. Nec 2000 Ips Command Manual An individual nec ips 2000 command manual could possibly have multiple name. Some refer to it as an owner's manual, an handbook, an end user handbook.
70-1 70-2 74-1 74-2 110-1 110-2 77-1 77-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 2/7 ND-45669 (E) ISSUE 2. 140-1 174-1 140-2 174-2 188-1 188-2 156-1 156-2 199-1 199-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 3/7 ND-45669 (E) ISSUE 2.
216-1 216-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 4/7 ND-45669 (E) ISSUE 2. 327-1 327-2 327-3 327-4 311-1 311-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 5/7 ND-45669 (E) ISSUE 2. ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 6/7 ND-45669 (E) ISSUE 2. ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 7/7 ND-45669 (E) ISSUE 2. ND-45669 (E) ISSUE 2 DECEMBER, 1997 NEAX2000 IVS Command Manual TABLE OF CONTENTS Page LIST OF FIGURES. LIST OF TABLES.
TABLE OF CONTENTS (CONTINUED) Page CM12 Station Class-1. CM13 Station Class-2. TABLE OF CONTENTS (CONTINUED) Page CM74 Stored Number for Station Speed Dialing. 247 CM76 Digit Conversion on DID Call.
TABLE OF CONTENTS (CONTINUED) Page CMD001 System Features (2).372 CMD003 Time Block Assignment. LIST OF FIGURES Figure Title Page Figure 2-1 CAT Key Assignment for ETJ-16DD-1. Figure 2-2 Line/Trunk Card Installation Location.
LIST OF TABLES Table Title Page Table 2-1 Function Keys. Table 2-2 Digit Keys. INTRODUCTION CHAPTER 1 INTRODUCTION 1.
PURPOSE This manual provides descriptions of the commands required for programming the NEAX2000 IVS (PBX) us- ing the Customer Administration Terminal (CAT) or Maintenance Administration Terminal (MAT). OUTLINE OF THE MANUAL This manual consists of the introduction (Chapter 1) and the following chapters:. This page is for your notes. CHAPTER 1 ND-45669 (E) Page 2 Revision 2.0. INFORMATION FOR DATA PROGRAMMING CHAPTER 2 INFORMATION FOR DATA PROGRAMMING 1. GENERAL This chapter provides information on the Customer Administration Terminal (CAT) and Maintenance Admin- istration Terminal (MAT) which are used as the man-machine interface with the PBX, and various tables used for indexing the commands by feature.
INFORMATION FOR DATA PROGRAMMING & – ← – – ← Figure 2-1 CAT Key Assignment for ETJ-16DD-1 CHAPTER 2 ND-45669 (E) Page 4 Revision 2.0. INFORMATION FOR DATA PROGRAMMING Table 2-1 Function Keys FUNCTION KEY MEANING Command entry start Execution of data write Cancel of key operation (Clear entry) Display of next data (Step forward) Separator; to be entered between two different data such as first/second data of CM72/74/ 90/97. INFORMATION FOR DATA PROGRAMMING 2.1.2 CAT Mode Setting Procedure To set CAT mode: 1. Press – CNF lamp flashes 2. Press – CNF lamp flashes – CNF, SPKR, ANS lamp on 3. Press – “CAT MODE” displayed on LCD –.
INFORMATION FOR DATA PROGRAMMING 2.2 CAT Operation When setting the office data, it is necessary to enter the following three kinds of data:. Command Code. First Data. Second Data An explanation of the data entry procedure follows: (a) Operation for confirming the existing office data + Command Code + + First Data +. INFORMATION FOR DATA PROGRAMMING (1) Example: When Station Number 300 is to be assigned to LEN 0000 and Station Number 301 to LEN 0001 by CM10 (Refer to Table 2-3.) Table 2-3 Assignment Operation (DISPLAY) STEP 1 Turn ON power switch. STEP 2 Press COMMAND =. INFORMATION FOR DATA PROGRAMMING (2) Example of Operating Steps for Correcting the Data Entry.
In Step 5 in Table 2-3, when is pressed after entering “0001” by mistake, press. Then the state returns to STEP 4. STEP 1 CM10 has been entered and has been pressed. INFORMATION FOR DATA PROGRAMMING 2.3 Error Messages When an erroneous operation is performed, or wrong data is entered, an error message is displayed on the LCD. Error messages and their meanings are shown in Table 2-4.
Table 2-4 Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION. INFORMATION FOR DATA PROGRAMMING 3. COMMAND REFERENCE TABLE 3.1 List of Commands Table 2-5 provides a list of commands.
Table 2-5 List of Commands COMMAND REMARKS CODE FUNCTION System Data Memory All Clear System Data Memory Partial Clear Setting of System Clock Log in/Log out of Password Mode Language Indicated on Multiline Terminal LCD Card Assignment. INFORMATION FOR DATA PROGRAMMING Table 2-5 List of Commands (Continued) COMMAND REMARKS CODE FUNCTION Function of RS-232C Interface Circuit System Timer Data System Counter Data/PAD Data/Trunk Restriction Class Conversion External Equipment Starting Condition Purpose of PBR/CFT Determination of Tone/Tone Source Digital Announcement Trunk PN-2DATA Common Route Indial. INFORMATION FOR DATA PROGRAMMING Table 2-5 List of Commands (Continued) COMMAND REMARKS CODE FUNCTION Multiline Terminal/SN610 ATTCON/Add-On Module Key Assignment Prime Line Multiline Terminal One-Touch Memory DSS Console Number DSS Console Key Assignment Add-On Module Number Multiline Terminal Soft Key Assignment Type of Data Adapter Data Terminal Attribute Data Nailed Down Connection. INFORMATION FOR DATA PROGRAMMING 3.2 Quick Reference Table of Commands Required for Service Feature This section provides a quick reference table of various commands related to each service feature. The features are listed alphabetically in the left column. Associated features (shown with bullets) are listed be- low the main features.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature: First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Account Code – 362/S 0 – 3 F/085 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Announcement Service – 124/S –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Attendant Console – (SN716 DESK CON) 02, 03 F/14 00, 01, 15. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Attendant Loop Release –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY.
Monitor – – 0 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Attendant Override – 012, 045, 076/S 0 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Call Distribution (ACD) –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Number Identification – –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Call Back – 156/0 03, 46 0 - 3 F/002 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY.
Call Forwarding - All Calls –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Call Forwarding - No Answer –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Split Call Forwarding - All Calls –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Split Call Forwarding - –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Call Pickup – – –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Centrex Compatibility 0 – 3 F/A58 16, 86 –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Consecutive Speed Dialing – F/19 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Dial Conversion – 050, 051/0 –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Direct Inward System Access –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Direct Station Selection/Busy Lamp –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Elapsed Call Timer – –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY External Paging with Meet-Me –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Flexible Ringing Assignment – 390/1 02, 07 68, 83, 84. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Hotline – 057/S – F/04 00 - 99 –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Automatic Intercom – 237/S –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Least Cost Routing 3/6 Digit 0 - 3 F/A26 - A28 51 - 55.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Message Reminder – 050, 051, 069, 148, 156, 208, 234 - 236, 280 - 294/S 47, 48. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Wide Area Telephone Service F/02 (WATS) Access Multiline Terminal Attendant. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Day/Night Mode Change by 0 –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Off-Premises Extension Pad Lock –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) F: First Data For Business System S: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Privacy/Privacy Release Private Line – 08/S Proprietary Multiline Terminal –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) F: First Data For Business System S: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY. Recall Key 16, 86 17/S F/F1009. This page is for your notes.
CHAPTER 2 ND-45669 (E) Page 44-2 Addendum-001 Revision 2.1 AUGUST, 1998. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY.
Ring Frequency Control –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Software Line Appearance – 01 –.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Step Call – 069, 163/1, 208/0 Supervisory Control of Peripheral Equipment 08/S. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Timed Reminder – 228/S –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Uniform Call Distribution (UCD) –. INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued): First Data For Business System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Voice Guide 95/S 12, 13, 14/S 00, 13 Voice Mail Integration –.
INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature: First Data For Hotel/Motel System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Wake-Up – 228, 282 – 284, 286, 287/S –. INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued): First Data For Hotel/Motel System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Do Not Disturb – 240,241/S 0 –. INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued): First Data For Hotel/Motel System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Maid Status – 281/S 0 –. INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued): First Data For Hotel/Motel System: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Single Digit Dialing 0 – 3 F/808 –.
INFORMATION FOR DATA PROGRAMMING 4. PRECAUTION 4.1 Conditions for Using Commands (1) Some commands require a system initialization (reset) after assignment/change of the office data, and oth- ers cannot be assigned/changed unless the system is in off-line mode (a state in which call processing is at a halt).
INFORMATION FOR DATA PROGRAMMING (2) When deleting data in any command, enter “CCC” as 2nd data. However, data in the following commands cannot be deleted.
Commands where the initial data ( ) is provided but the initial data ( ) is “NONE”. INFORMATION FOR DATA PROGRAMMING (b) Operation for changing off-line mode to on-line mode:. Set SW1 as shown below.: POSITION TO BE SET For details, refer to the Circuit Card Manual. 4.3 Method for Installing Line/Trunk Cards In the PBX, all line/trunk circuits are provided by installing the cards into a card shelf.
The PBX employs a flexible port assignment architecture in which the system allocates a port (Time Slot) to each LEN (Line Equipment Number) according to system data. INFORMATION FOR DATA PROGRAMMING. Number of ports on each card Each card slot has four (4) LENs. For the relation between Slot Numbers and LENs, refer to the “Port Assignment Table” of the Office Data Programming Manual. Table 2-9 Port Assignment on Each Line/Trunk Card X: Assignment possible –: Assignment not possible LEN TO BE ASSIGNED ON EACH LTXX.
INFORMATION FOR DATA PROGRAMMING 4.4 Password Entry In a system with password service, a maintenance person is required to enter an authorization level num- ber (Password Level) and appropriate password prior to engaging in programming the system data with the MAT/CAT. A maximum of eight (8) Password Levels can be set up. The number of commands that the maintenance person can access is determined by the password level. This page is for your notes.
CHAPTER 2 ND-45669 (E) Page 60 Revision 2.0. DESCRIPTION OF COMMANDS CHAPTER 3 DESCRIPTION OF COMMANDS 1. GENERAL This chapter provides a detailed description for each command. DETAILED DESCRIPTION OF COMMANDS This section describes the methods for programming commands. Information about each command is present- ed in the following order: (1) Function: The function of the command.
CM00 System Data Memory All Clear CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR FUNCTION: This command confirms that the system data memory (RAM) area can be Written-in /Read-out and also assigns the Initial Data to the RAM area. PRECAUTION: (1) This command can only be used in off-line mode. CM01 System Data Memory Partial Clear CM01 COMMAND CODE TITLE: SYSTEM DATA MEMORY PARTIAL CLEAR FUNCTION: This command is used to clear the data associated with the Numbering Plan (CM20-CM29) or Toll Restriction (CM85-CM8A). PRECAUTION: This command can only be used in off-line mode.
ASSIGNMENT PROCEDURE: + 01 + Commands to be cleared: 20, 21, 22, 23, 24, 25, 26 and 29 in Data Memory. CM02 Setting of System Clock CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK FUNCTION: This command is used to assign clock data (day, date and time). PRECAUTION: (1) The system clock starts when EXE is depressed.
(2) Reenter all the Clock Data if “HARD ERROR” is displayed as a result of this command. (3) This command is included in MAT mode menu “E1”. CM03 Log In/Log Out of Password Mode CM03 COMMAND CODE TITLE: LOG IN/LOG OUT OF PASSWORD MODE FUNCTION: This command is used to enter a password which allows authorized personnel to access commands in accordance with preassigned authorization levels. PRECAUTION: None ASSIGNMENT PROCEDURE: To log in the password mode and enter the password.
CM04 Language Indicated on Multiline Terminal LCD CM04 COMMAND CODE TITLE: INITIAL LANGUAGE INDICATED ON MULTILINE TERMINAL LCD FUNCTION: This command selects the language that displays on the Multiline Terminal LCDs. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 2ND DATA 1ST DATA. CM05 Card Assignment CM05 COMMAND CODE TITLE: CARD ASSIGNMENT FUNCTION: This command is used to inform the main processor card (CP00 or CP03) of the SENSE switch (sense wheel) setting on each AP circuit card that is installed. PRECAUTION: (1) This command requires a system reset after setting the data. (2) This command is included in MAT mode menu “E2”.
CM05 COMMAND CODE TITLE: CARD ASSIGNMENT Note: Set the SENSE switch on the AP circuit card to match an unequipped slot number as shown below. SENSE WHEEL (04 - 15) SWITCH SETTING VALUE CHAPTER 3 ND-45669 (E) Page 68 Addendum-001 Revision 2.1 AUGUST, 1998. CM06 Misc. Trunk Number Assignment CM06 COMMAND CODE TITLE: MISC. TRUNK NUMBER ASSIGNMENT FUNCTION: This command assigns Miscellaneous Trunk Numbers to each card. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 06YY + (1-4 digits) (2-4 digits).
CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT FUNCTION: This command assigns the DTI/ISDN trunks. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 07YY + (4 digits) (4 digits) DATA TABLE: 1ST DATA 2ND DATA RELATED. CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING 32XX Virtual Channel No. DXXX Trunk Number (D000 – D255) 32 XX Note: Trunk numbers already assigned by Home-Side Trunk CM10 cannot be Virtual Channel used.
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 70-2 Addendum-002 Revision 2.2 JANUARY, 1999. CM08 Basic Service Features CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES FUNCTION: This command is used to assign basic features on a system-wide basis. PRECAUTION: After setting 1st data 390 and 391, system reset is required. ASSIGNMENT PROCEDURE: BASIC SERVICE DATA (0/1) + 08 + FEATURE.
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES DATA TABLE: Initial Data BASIC SERVICE FEATURE SETTING DATA Busy Verification Not available Available Attendant Loop Release Provided Not provided When the system is in night mode, an attendant (dial “0”) call Not transferred from a station is automatically transferred to a specific sta- To transfer tion. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Toll Restriction for outgoing call by System Speed Dialing Not provided feature. Provide Warning tone sent to connected parties during Executive Only once Override or Attendant Override. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA This setting determines the trunk seizing sequence when CM Highest available trunk 35 YY = 83 is set to 0. Lowest available trunk Note: When NEAX 2000/1000IVS is installed with loop- start trunks, it is important to select the highest available trunk setting to prevent call collisions. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA 1000-Slot Memory Block Number “3” for Station Speed Di- Available (See CM20, A50) aling is used as the Memory Block for System Speed Dialing. Not available 1000-Slot Memory Block Number “1”.
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E) Page 74-2 Addendum-001 Revision 2.1 AUGUST, 1998. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Outgoing C.O. Line Call from a Station to Station connection. Not allowed To allow Answer preference for enhanced Trunk Direct Appearance Display 2-digit trunk ID code (CM30 YY = 19, last two digits assigned) Display 4-digit trunk ID code (CM30 YY = 19). CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA A trunk line placed in Consultation Hold by Call Park-Sys- Not available tem/Tenant, can be retrieved by pressing a trunk line appear- Available ance key on any Multiline Terminal. Periodic Time Indication Tone Sending for C.O.
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES: Initial Data BASIC SERVICE FEATURE SETTING DATA In delay-type paging, when the paged party encounters a busy To set paging circuit, Call Back is automatically set. (Applicable to Not set both Radio Paging and Speaker Paging.) Restriction of a station to station call between tenants by To cancel CM63 Y=1 is temporarily cancelled by external key. CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING 32XX Virtual Channel No. DXXX Trunk Number (D000 – D255) 32 XX Note: Trunk numbers already assigned by Home-Side Trunk CM10 cannot be Virtual Channel used. This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 70-2 Addendum-002 Revision 2.2 JANUARY, 1999.
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES: Initial Data BASIC SERVICE FEATURE SETTING DATA 1000-Slot Memory Block Number “2” for Station Speed Di- Available aling is used as the Memory Block for System Speed Dialing. Not available Last Number Redial feature for DP/DTMF telephone. Available (See CM20 - 069) Not available Last Number Redial/Stack Dial for internal calls. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Diversion display by ATTCON. Available Not available LDN Diversion by ATTCON.
Available (See CM58) Not available Trunk to Trunk Transfer by an Attendant before answer (on Available the OG trunk). CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Trunk access from a station in Room Cut-Off Status. Restricted to C.O. Only Restricted to all Trunk Routes. Message Waiting lamp of calling station is extinguished when Assigned an attendant answers (See CM13-13) Not assigned. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Destination of Priority Call 0.
Same station as Off-Hook Alarm. (See CM51 YY = 12) Terminate to ATTCON. (See CM46 -54) Destination of Priority Call 1. Same station as Off-Hook Alarm. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Call termination to My Line while the extension makes a call Restricted with a secondary extension or trunk line on Multiline Termi- Allowed nal. Note: When 0 (Restricted) is set, 0 (Station Base) should be set by CM08-269.
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Display last calling station number. 6 seconds Note: This is only applicable for an ETJ-16DC-1, an ETJ- Until next call 16DD-1 or an ETJ-24DS-1.
On a Tie Line outgoing call with answer signal, transferring/ Not available holding the call before distant called station answers. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Confirmation tone after dialing the access code for Account No tone Code/Authorization Code/Forced Account Code. Service Set Tone (SST) For the Automated Attendant call, caller dials while sending Not allowed (Allowed after sending message or music. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Centralized Billing-CCIS feature for local office To provide (for local office) Not provided (for centralized office, INITIAL MP Reset) Maximum number of dialed digits sent to CCIS network 24 digits (Tandem calls over 16 digits and name display) 16 digits.
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Consecutive Speed Dialing when making an ISDN call. Available Not available Method of charging a transferred call (for use with CP03 Charging to the transferring station or (MP) only) the transfer destination station. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Forced release when a called ISDN Terminal is no answer Not available during 3 minutes Available Assignment of the calling party number which is sent to an Calling Party No. CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Sending ANI/Caller ID/CPN to the OAI terminal. Available Not available Sending ANI/Caller ID/CPN to the SMDR terminal. Available Not available OAI–TSAPI Same as NEAX2400 (recommended setting) SCF1 facility SMFN Off-Hook indication sent Requiring ANI Signal/Caller ID from network when an in. CM09 Additional Service Features CM09 COMMAND CODE TITLE: INITIAL ADDITIONAL SERVICE FEATURES FUNCTION: This command is used to assign additional features on a system-wide basis.
PRECAUTION: None ASSIGNMENT PROCEDURE: ADDITIONAL SERVICE DATA (0/1) ST + 09 + DE + + DE + + EXE FEATURE (2 digits). CM10 Station Number, Trunk Number, Card Number CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER FUNCTION: This command is used to assign Station Numbers, Trunk Numbers, and Card Numbers to LENs (Line Equipment Numbers). PRECAUTION: (1) When deleting a Station Number (Single Line or Multiline Terminal), be sure to delete Call Pickup data (CM 16), UCD Group data (CM17) and Station Hunting Group data (CM18) in advance. CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER DATA TABLE: SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0000 Single Line Station Number (1-4 digits) x=0-9, A (.), B (#) Note: When assigning a 5-digits station, assign the last four digits in 0511 xxxx CM10. CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0124 E200 Circuit Number of DTMF Receiver (PN-CP03) INITIAL E203 0000 E600 TAS Equipment Interface activated by Station Ringer. CM30 (Use of LC card) YY = 13, 14, 17. CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0000 ISDN Circuit Station Number represents ISDN Circuit Station Number INITIAL EFXXXX X: 0-9, A(.), B(#) 0511 ND-45669 (E) CHAPTER 3.
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER. The relation between the locations of the card and the LENs (0000–0511) is shown below. 0195 0199 0203 0207 0211 0215 0219 0223 0227 0231 0235 0239 0243 0247 0251 0255 0194. CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER 0451 0455 0459 0463 0467 0471 0475 0479 0483 0487 0491 0495 0499 0503 0507 0511 0450 0454 0458 0462 0466 0470 0474 0478 0482 0486 0490 0494 0498 0502 0506 0510 0449. CM11 Virtual-Line Number CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER FUNCTION: This command is used to assign station numbers, Intercom numbers, Loop Line numbers and ICI/OPR Line numbers (for a Multiline Terminal Attendant Position), to Virtual-Lines assigned on a Multiline Terminal. PRECAUTION: (1) The Virtual-Line station numbers must be different from station numbers assigned by CM10. CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER VIRTUAL RELATED VIRTUAL-LINE NUMBER COMMAND Note 0000 A200 Manual Intercom Number (Refer to CM12 YY = 03 CM56 YY = 11 0255 A700 CM90 Manual Intercom Group No.
A201 (00-24) A701 Sequential Number in Group (2-7) A224 A724 Note. CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER Note 1: Automatic Intercom Numbers are assigned as shown below: AUTOMATIC AUTOMATIC AUTOMATIC INTERCOM INTERCOM INTERCOM GROUP No.(A) No.(B) A000 A100 A001 A101 A031 A131 Note 2: Manual Intercom Numbers are assigned as shown below: MANUAL INTERCOM GROUP.
CM12 Station Class-1 CM12 COMMAND CODE TITLE: STATION CLASS-1 FUNCTION: The features for each station are determined by assigning Station Class-1 to each station number. PRECAUTION: (1) When assigning Station Class-1 to Multiline Terminal using this command, enter “X-XXXX (Pri- mary Extension Number)”. CM12 COMMAND CODE TITLE: STATION CLASS-1 ASSIGNMENT PROCEDURE: Automatic/ ICI/OPR DATA Loop STATION Manual/ + DE + + EXE Line No. (1-4 digits) ST + 12YY + DE + Dial Intercom (4 digits) (4 digits) (1-4 digits) No. (4 digits) DATA TABLE: Initial Data SETTING DATA.
CM12 COMMAND CODE TITLE: STATION CLASS-1: Initial Data SETTING DATA MEANING DATA MEANING Kind of Telephone House Phone 0 (TEL) House Phone 1 (See CM51 YY=14) House Phone 2 House Phone 3 FAX Call Station Group No. 0 FAX Call Station Group No.
1 Note 1 FAX Call Station Group No. CM12 COMMAND CODE TITLE: STATION CLASS-1: Initial Data SETTING DATA MEANING DATA MEANING Trunk to be seized as a D000 Trunk Number (PVTRK) Private Line on a per sta- tion basis D255 Related Commands: CM35 YY=98, CM42-08 Combination of the main Main Station Number/Sub Station Number Note 5, Note 6 station and sub station.
CM12 COMMAND CODE TITLE: STATION CLASS-1 1st LEN 2nd through 4th LEN X: Available (Level 0) Note 1 (Level 1-3) Note 2 –: Not available Series E (Series E mode)/Series III/E-Pro Series E (Series E mode)/Series III/E-Pro Series E (Series E mode/Series III mode) ATTCON/DSS Console ATTCON/DSS Console Series E (Series E mode)/Series III/ E-Pro/. CM13 Station Class-2 CM13 COMMAND CODE TITLE: STATION CLASS-2 FUNCTION: The features for each station are to be designated by assigning Station Class-2 for each station number. PRECAUTION: (1) When assigning Station Class-2 to a Multiline Terminal by this command, enter “X-XXXX (Pri- mary Extension Number)”.
CM13 COMMAND CODE TITLE: STATION CLASS-2 ASSIGNMENT PROCEDURE: STATION DATA ST + 13YY + DE + DE + + EXE NUMBER (1 digit) (1-4 digits) DATA TABLE:: Initial Data SETTING DATA MEANING DATA MEANING Do Not Disturb-System To provide (DNDS) Not provided Room Cut Off-System. CM13 COMMAND CODE TITLE: STATION CLASS-2: Initial Data SETTING DATA Ordinary Station or Front Station Message Waiting Front Desk Instrument (FRONT) Ordinary Station Note: MW Lamp of calling station is turned off when Message Wait- ing Front Desk Terminal an- swers (see CM08-233).
CM15 Service Restriction Class CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS FUNCTION: The restriction of each feature is to be set for each service restriction class assigned to the stations. There are three kinds of Service Restriction Class: A, B and C.
The service features to be restricted by these Service Restriction Classes are different. CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS DATA TABLE: Service Class A: Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Call Forwarding – All Calls Restricted Allow Call Hold Trunk Queueing – Outgoing Call Back Guest Name Display via PMS Allow Restricted.
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A: Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Message Waiting Lamp set/reset from the sta- Restricted tion Allow Timed Queue Call Forwarding – All Calls – Outside Call Forwarding –. CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A: Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Camp-On by Station (Call Waiting Method) Restricted (Answer - Called Side) Allow Call Back - Multiple Assignment Message Reminder (Setting Side) Message Reminder (Set Side) Internal Zone Paging Access/All Zone Internal. CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A: Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) PS Call Forwarding-Not Available Allow Restricted Voice Guide (Validity of data set by CM48 Y=2 Restricted first data 12, 13, 14.) Allow Roaming Service Allow. This page is for your notes.
THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 110-2 Addendum-001 Revision 2.1 AUGUST, 1998.
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class B: Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) TAS Service Restricted Allow Individual Trunk Access from station Change of mode for CAT Starting up MSF from PB telephone/Multiline Terminal by using an access code Day/Night Mode Change by Station Dialing Periodic Time Indication Tone Sending. CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class C: Initial Data YY/YYY SERVICE SETTING DATA REST.
MEANING DATA MEANING CLASS (C) Immediate Ringing on Single Line Station Restricted Allow One hit ringing for Call Forwarding-All Calls Restricted Allow Ringing Line Pick-up Allow Restricted. CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Note 1: The tone indication pattern is assigned by the combination of data in YY=83 and YY = 84: Initial Data MEANING OF DATA Setting Data 600 + 700 Hz Modulating Signal 1024 + 1285 Hz/16 Hz Modulating Signal 480 + 606 Hz/8 Hz. CM16 Call Pickup Group/Group Diversion Group CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP FUNCTION: This command is used to assign stations to a Call Pickup Group and a Group Diversion Group.
PRECAUTION: (1) The maximum number of stations which can be assigned to a Call Pickup Group is 60. (2) There is no limitation to the number of Call Pickup Groups. CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP DATA TABLE: STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Assignment of Station Station Numbers (A) Station Number (B) Numbers to be included in a Call Pickup Group XXXX XXXX When assigning station numbers to a Call Pickup Group, only two station numbers can be assigned per operation.
CM17 UCD Group CM17 COMMAND CODE TITLE: UCD GROUP FUNCTION: This command is used to define ACD (Automatic Call Distribution) / UCD (Uniform Call Distribution) groups. PRECAUTION: (1) A maximum of 16 ACD / UCD groups can be assigned per system. (2) A maximum of 60 stations can be assigned to an ACD / UCD group. CM17 COMMAND CODE TITLE: UCD GROUP Initial Data STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Assignment of the Pi- Station Number to be Member Station (Pilot lot Station in the assigned as Pilot Pilot Station ACD/UCD Group XXXX No.).
CM18 Station Hunting Group CM18 COMMAND CODE TITLE: STATION HUNTING GROUP FUNCTION: This command is used to assign stations to a Station Hunting Group. There are three hunt types: Pilot System, Circular System and Switch Back System. PRECAUTION: (1) When a Station Hunting Group requires a secretary station, it is necessary to assign Y=2. (2) The maximum number of stations which can be assigned to a Station Hunting Group is 60. CM18 COMMAND CODE TITLE: STATION HUNTING GROUP DATA TABLE: Pilot System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station num- Station Number (A)/ Station Number (B)/ bers included in a Station Data Station Number (A) Data Station Number (B) Hunting Group XXXX. CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary Station: Secretary Station Number Secretary Station Serial If an incoming call ter- Numbers: minated to a Station XXXX Serial Numbers to be as- Hunting Group has en- signed to Secretary Station countered all lines busy. CM18 COMMAND CODE TITLE: STATION HUNTING GROUP (2) Circular System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station Station Number (A)/ Station Number (B)/ Numbers included in a Data Station Number (A) Data Station Number (B) Station Hunting Group XXXX XXXX.
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP (3) Switch Back System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station Num- Station Number (A) / Station Number (B) / bers included in a Station Data Station Number (A) Data Station Number (B) Hunting Group. CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary Station: Secretary Station Number Secretary Station Serial Same as Pilot System Number: XXXX Example: (Same as Pilot System) Data can be set to all stations belonging to the Switch Back Secretary System. CM19 Secretary/Group Diversion Station Number CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER FUNCTION: Station numbers corresponding to Secretary Station Serial Numbers are to be assigned. The assigned numbers are called Secretary Station Numbers. Also, Station numbers are to be assigned as destination stations for Group Diversion. CM1A Data Station Number CM1A COMMAND CODE TITLE: INITIAL DATA STATION NUMBER FUNCTION: This command is used to assign the Data Station Numbers for accommodating the data terminals via the Multiline Terminal.
PRECAUTION: (1) This command requires a system reset after setting the data. (2) This command is included in MAT mode menu “A1”. CM1B ISDN Terminal Multipoints Station Number Assignment CM1B COMMAND CODE TITLE: ISDN TERMINAL MULTIPOINTS STATION NUMBER ASSIGNMENT FUNCTION: This command is used for an ISDN Terminal Multipoints Station Number. PRECAUTION: None ASSIGNMENT PROCEDURE: ISDN ISDN CIRCUIT DATA MULTIPOINTS No.
+ EXE + 1B + STATION No. CM1C PS Station Number Assignment CM1C COMMAND CODE TITLE: PS STATION NUMBER ASSIGNMENT FUNCTION: This command is used to assign the PS Station Numbers for providing the Wireless Communication System. PRECAUTION: None ASSIGNMENT PROCEDURE: ST + 1C + DE + VIRTUAL PS No. PS STATION No.
CM1D PS-ID Assignment/PS Operation Data Download CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT/PS OPERATION DATA DOWNLOAD FUNCTION: This command is used to assign the PS-ID and to download the PS Operation data. PRECAUTION: (1) When a PS is set up initially, set the PS in Data Download Mode by applying power to the PS while pressing the SEND key, and then execute the CM1DYY=20 in Calling Area No. CM20 Numbering Plan CM20 COMMAND CODE TITLE: NUMBERING PLAN FUNCTION: Trunk routes and features are assigned access codes. Required developments (Route Advance, Tenant, Kind of Calling Terminal and Closed Number data) and trunk routes or features are assigned access codes with CM22, CM23, CM24 and CM26. The following figure shows the relationship between com- mands: For each access code Numbering Plan. CM## Title - After typing title, apply default character tag and then TOC paragraph tag. CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT PROCEDURE: DATA ACCESS CODE ST + 20Y + DE + + DE + + EXE (3 digits) (1-3 digits) DATA TABLE: RELATED ACCESS CODE.
As Ozzie said, nothing to monitor ISDN service, but you do have a few commands EA0 DE 00 - will list all alarms that the system shows and a description. This is where you can look to see if your digital lines (ISDN) had outages or errors. Any other issue the system has you can see it here also. Command - EA1 DE 00 - Clear all MJ/MN alarms - EA1 DE 01 - Clear MJ alarms - EA1 DE 02 - Clear MN alarms Phillip E. Porter Senior Systems Engineer Telecommunication Solutions Group, Inc.
(TSG) RE: Maintenance Commands NEAX 2000 IPS (MIS) 4 Mar 10 10:59.